![openbox v8s keeps freezing openbox v8s keeps freezing](https://m.media-amazon.com/images/I/51xr8LAYf5L._AC_SY355_.jpg)
- #OPENBOX V8S KEEPS FREEZING INSTALL#
- #OPENBOX V8S KEEPS FREEZING SERIAL#
- #OPENBOX V8S KEEPS FREEZING FULL#
- #OPENBOX V8S KEEPS FREEZING SOFTWARE#
- #OPENBOX V8S KEEPS FREEZING PC#
#OPENBOX V8S KEEPS FREEZING SERIAL#
Well i at least have had success with my openbox s10.like many others on here my s10 died completely, after a few checks i confirmed the psu was ok.I tried emugrade and got similer messages as other users ranging from sy mem error to no serial port detected.so i ordered some new flash chips U39 on s10 and a spi programmer.I carefully removed the flash chip and read it fine on my spi programmer. Try using the recovery tool I posted above
#OPENBOX V8S KEEPS FREEZING PC#
You get the 'synchronizing stb reset target' when your pc is not communicating with the stb:ġ.Check you are using the correct com port by going to device managerĢ.Make sure you have ticked the include boot loader option
![openbox v8s keeps freezing openbox v8s keeps freezing](https://i.ytimg.com/vi/BbvAcwH5Uhc/maxresdefault.jpg)
So i am currently at my wits end on this one erom_upgrade_8Mflash, Upgrade_PVR800 HD Tool, F3_X3_M3_Q3_RS232_UpgradeTool I've used different verions of the recovery software. second based on the reality of f3 internal connections 2-3,3-2, 5-5 third was breakout jumper board modded to include all possible connections and still no luck and each cable has been tested over 10 second increments upto 2 min then to 4 mins on each attempt i've used different ports different pc's different OS, win 7 vista and xp and still cannot get past sync stb
#OPENBOX V8S KEEPS FREEZING FULL#
I'm using a genuine serial port and so far i have made three null cables one based on the first post pinouts with full handshake. I read this post from top to bottom and went ahead with the null modem repair and it wont connect all i get is synchronizing stb reset target My F3 box fugged up this morning i loaded aj new channel list, powered off then on now the screen is stuck on load and thats it no power off or on, no on screen action If you don't have a backup of your image just download
#OPENBOX V8S KEEPS FREEZING SOFTWARE#
I used the software on page 6 of this thread and my backup. I bought a female/female null modem cable and used it on an old dell pc running windows xp. Perhaps you would be better truing the Null modem lead on an older computer that has a hard wired RS232 port, It has been reported that USB to Serial adaptors do not work on some receivers.Įven newer PC's still have an on board connector to add an external RS232 also thats what i did the adaptor cost a little more than the Null modem lead itself how can i know the firmware factory? so all people tell yes i got,i'm able to revive my skybox,please tell more details what type of problem and how you have solve.there is my situation,anyone can tell me where is the problem,thanks.i will go to test it with null modem serial rs232 but i want to know if are problem hardware so i not go to spend for cable,i have spend 7 euro for rs232 null modem usb that not work.thanks again.:canabis: Usb nul modem don't work,my situation.my skybox f3 was dead and dont turn on anymore,no signs,no led,nothing (i dont know if has an hardware problem or software problem so i ask who have the same problem,have you an skybox f3 with no turn on?) my skybox when i switch on related on TV with hdmi not have any signs so is problem of hardware?. I use same cabel and other cabel made myself also, one dead skybox s11 responding well and get live back but other dead skybox s11 not rsponding and box has no problem with power supply You are right,but when box not responding by same cabel as you say,then.
![openbox v8s keeps freezing openbox v8s keeps freezing](https://www.strongiptv.co.uk/wp-content/uploads/2020/01/how-to-setup-iptv-on-a-openbox-v8s.jpg)
#OPENBOX V8S KEEPS FREEZING INSTALL#
To connect to the box after only a couple attempts or first time you MUST use the correct cable as i was getting nowhere!Īlso on these copy prolific cables if you are getting errors installing it's because you used windows server which won't work the driver and cable won't match, delete the cable in device manager, disable your internet and then re-insert the cable and install with the CD provided and it will work perfectly. Straight wired is obviously 2-2, 3-3 & 5-5 which is not compatible even if you are using an automatic handshaking usb lead with prolific IC, at least it didnt work in my case. I used a cheap ebay (?1.67 delivered) usb-rs232 lead which claimed to have automatic handshaking so it should therefore have worked with any basic female rs232 female cable like a straight-wired one but it doesnt! The only way i could get the thing to flash the firmware was to make my own NULL cable out of the straight wired i bought.(i'm an electronics techy so have a soldering iron handy etc) but anyone else should just buy a female NULL cable.Īs has already been mentioned This box uses only 3 pins/wires to connect to your computer via rs232 but they link in NULL format which is 2-3, 3-2 & 5-5.
![openbox v8s keeps freezing openbox v8s keeps freezing](https://www.foofighters.fm/wp-content/uploads/2021/04/Android-TV-Box-Freezing-On-Startup-Fix-6.png)
I think one of the main issues here is people havent explained that a 'NULL' cable is absolutely essential to perform this box flash.